-
-
Available Formats
- Options
- Availability
- Priced From ( in USD )
-
Available Formats
-
- Immediate download
- $52.00
- Add to Cart
-
- Printed Edition
- Ships in 1-2 business days
- $52.00
- Add to Cart
Customers Who Bought This Also Bought
-
ASTM D1157-23
Priced From $50.00 -
ASTM D1016-05(2015)
Priced From $67.00 -
ASTM D3505-18
Priced From $76.00 -
ASTM E659-15(2023)
Priced From $57.00
About This Item
Full Description
1.1''This test method covers the determination of the flash point of liquid and solid chemical compounds flashing from below''''''10 to 370''C (16 to 700''F). The procedures and apparatus in Test Methods D56, D93, D3278, D3828, and D3941 are to be used. Modification to these procedures are specified for tests on solids and viscous liquids. The significance of the results obtained is discussed along with possible sources of error and factors that might cause interference.
1.2''Suggestions for adapting this procedure to mixtures of chemicals are included (see Appendix X2).
1.3''This test method should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials or assemblies under actual fire conditions. However, results of this test method may be used as elements of a fire risk assessment that take into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use.
1.4''The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.5''Warning'''Mercury has been designated by the United States Environmental Protection Agency (EPA) and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA'''s website ''' http://www.epa.gov/mercury/faq.htm ''' for additional information. Users should be aware that selling mercury or mercury-containing products, or both, into your state may be prohibited by state law.
1.6''This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See also Section 8.
1.7''This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Document History
-
ASTM E502-21a
viewing
Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods- Most Recent
-
ASTM E502-21
Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods- Historical Version
-
ASTM E502-07(2013)
Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods- Historical Version
-
ASTM E502-07
Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods- Historical Version
-
ASTM E502-07e1
Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods- Historical Version
-
ASTM E502-06a
Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods- Historical Version
-
ASTM E502-06
Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods- Historical Version
-
ASTM E502-84(2000)
Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods- Historical Version
-
ASTM E502-84(1994)
Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods- Historical Version